ZoneRules

Gets the amount of daylight savings in use for the specified instant in this zone.

This provides access to historic information on how the amount of daylight savings has changed over time. This is the difference between the standard offset and the actual offset. Typically the amount is zero during winter and one hour during summer. Time-zones are second-based, so the nanosecond part of the duration will be zero.

Gets a suitable offset for the specified local date-time in these rules.

The mapping from a local date-time to an offset is not straightforward. There are three cases:

• Normal, with one valid offset. For the vast majority of the year, the normal case applies, where there is a single valid offset for the local date-time.
• Gap, with zero valid offsets. This is when clocks jump forward typically due to the spring daylight savings change from "winter" to "summer". In a gap there are local date-time values with no valid offset.
• Overlap, with two valid offsets. This is when clocks are set back typically due to the autumn daylight savings change from "summer" to "winter". In an overlap there are local date-time values with two valid offsets.

Thus, for any given local date-time there can be zero, one or two valid offsets. This method returns the single offset in the Normal case, and in the Gap or Overlap case it returns the offset before the transition.

Since, in the case of Gap and Overlap, the offset returned is a "best" value, rather than the "correct" value, it should be treated with care. Applications that care about the correct offset should use a combination of this method, #getValidOffsets(LocalDateTime) and #getTransition(LocalDateTime).

Gets the offset applicable at the specified instant in these rules.

The mapping from an instant to an offset is simple, there is only one valid offset for each instant. This method returns that offset.

Gets the standard offset for the specified instant in this zone.

This provides access to historic information on how the standard offset has changed over time. The standard offset is the offset before any daylight saving time is applied. This is typically the offset applicable during winter.

Gets the offset transition applicable at the specified local date-time in these rules.

The mapping from a local date-time to an offset is not straightforward. There are three cases:

• Normal, with one valid offset. For the vast majority of the year, the normal case applies, where there is a single valid offset for the local date-time.
• Gap, with zero valid offsets. This is when clocks jump forward typically due to the spring daylight savings change from "winter" to "summer". In a gap there are local date-time values with no valid offset.
• Overlap, with two valid offsets. This is when clocks are set back typically due to the autumn daylight savings change from "summer" to "winter". In an overlap there are local date-time values with two valid offsets.

A transition is used to model the cases of a Gap or Overlap. The Normal case will return null.

There are various ways to handle the conversion from a LocalDateTime. One technique, using this method, would be:

ZoneOffsetTransition trans = rules.getTransition(localDT);
if (trans == null) {
// Gap or Overlap: determine what to do from transition
} else {
// Normal case: only one valid offset
zoneOffset = rule.getOffset(localDT);
}

Gets the list of transition rules for years beyond those defined in the transition list.

The complete set of transitions for this rules instance is defined by this method and #getTransitions(). This method returns instances of ZoneOffsetTransitionRule that define an algorithm for when transitions will occur.

For any given ZoneRules, this list contains the transition rules for years beyond those years that have been fully defined. These rules typically refer to future daylight saving time rule changes.

If the zone defines daylight savings into the future, then the list will normally be of size two and hold information about entering and exiting daylight savings. If the zone does not have daylight savings, or information about future changes is uncertain, then the list will be empty.

The list will be empty for fixed offset rules and for any time-zone where there is no daylight saving time. The list will also be empty if the transition rules are unknown.

Gets the complete list of fully defined transitions.

The complete set of transitions for this rules instance is defined by this method and #getTransitionRules(). This method returns those transitions that have been fully defined. These are typically historical, but may be in the future.

The list will be empty for fixed offset rules and for any time-zone where there has only ever been a single offset. The list will also be empty if the transition rules are unknown.

Gets the offset applicable at the specified local date-time in these rules.

The mapping from a local date-time to an offset is not straightforward. There are three cases:

• Normal, with one valid offset. For the vast majority of the year, the normal case applies, where there is a single valid offset for the local date-time.
• Gap, with zero valid offsets. This is when clocks jump forward typically due to the spring daylight savings change from "winter" to "summer". In a gap there are local date-time values with no valid offset.
• Overlap, with two valid offsets. This is when clocks are set back typically due to the autumn daylight savings change from "summer" to "winter". In an overlap there are local date-time values with two valid offsets.

Thus, for any given local date-time there can be zero, one or two valid offsets. This method returns that list of valid offsets, which is a list of size 0, 1 or 2. In the case where there are two offsets, the earlier offset is returned at index 0 and the later offset at index 1.

There are various ways to handle the conversion from a LocalDateTime. One technique, using this method, would be:

List validOffsets = rules.getOffset(localDT);
if (validOffsets.size() == 1) {
// Normal case: only one valid offset
zoneOffset = validOffsets.get(0);
} else {
// Gap or Overlap: determine what to do from transition (which will be non-null)
ZoneOffsetTransition trans = rules.getTransition(localDT);
}

In theory, it is possible for there to be more than two valid offsets. This would happen if clocks to be put back more than once in quick succession. This has never happened in the history of time-zones and thus has no special handling. However, if it were to happen, then the list would return more than 2 entries.

Checks if the specified instant is in daylight savings.

This checks if the standard and actual offsets are the same at the specified instant.

Checks of the zone rules are fixed, such that the offset never varies.

Checks if the offset date-time is valid for these rules.

To be valid, the local date-time must not be in a gap and the offset must match the valid offsets.

Gets the next transition after the specified instant.

This returns details of the next transition after the specified instant. For example, if the instant represents a point where "Summer" daylight savings time applies, then the method will return the transition to the next "Winter" time.

Gets the previous transition before the specified instant.

This returns details of the previous transition after the specified instant. For example, if the instant represents a point where "summer" daylight saving time applies, then the method will return the transition from the previous "winter" time.